IPH-24B-6.5-25-11

IPH-24B-6.5-32-11
IPH-24B-8-20-11

IPH-24B-8-25-11

IPH-24B-8-32-11

IPH-25B-3.5-40-11

IPH-25B-3.5-50-11

IPH-25B-3.5-64-11
IPH-25B-5-40-11

取油時，應將油桶臥置于一高度適當?shù)哪炯苌?，在桶面的蓋口處配以龍頭放油，并在龍頭下放一容器，以防滴濺?；?qū)⒂屯爸狈艔耐吧w口插入油管通過手搖泵取油。Z2FS16-3X/S2
Z2FS16A-2-5X
Z2FS22-3X/S2
Z2FS6
Z2FS6-14X/2Q
Z2FS6-2-43/1QV
Z2FS6-2-4x/
Z2FS6-2-4X/2Q
Z2FS6-2-4x/2QV
Z2FS6-5-43/2QV
Z2FS6-5-4X/2Q
P7600-F180NU3886/F125NPB-1蘭溪生產廠家QX514郴州生產廠家http://www.qihuiwang.com/product/q35526/241910261.html生產廠家

IPH-25B-5-50-11

IPH-25B-5-64-11
IPH-25B-6.5-40-11

IPH-25B-6.5-50-11

IPH-25B-6.5-64-11
IPH-25B-8-40-11

IPH-25B-8-50-11

P7600-F180NU3886/F125NPB-1蘭溪生產廠家 IPH-25B-8-64-11

IPH-26B-3.5-80-11

IPH-26B-3.5-100-11

IPH-26B-3.5-125-11
IPH-26B-5-80-11

IPH-26B-5-100-11

主動軸襯套孔與從動軸孔磨損的修理:主動軸襯套孔磨損后，可用鉸削方法消除磨損痕跡，然后配用加大至相應尺寸的襯套。從動軸孔磨損也以鉸削法消除磨損痕跡，然后按鉸削后孔的實際尺寸配制從動軸NXQ2-L100/31.5-H
NXQ2-L150/31.5-H
蓄能器NXQ2-F0.25/10-H
NXQ2-F0.4/10-H
NXQ2-F0.63/10-H
蓄能器NXQ2-F1/10-H
NXQ2-F1.6/10-H
NXQ2-F2.5/10-H
蓄能器NXQ2-F4/10-H
NXQ2-F6.3/10-H
P7600-F180NU3886/F125NPB-1蘭溪生產廠家P5100-F100NM45797/P124-G10Y03G黑龍江生產廠家http://www.qihuiwang.com/product/q35527/267303325.html生產廠家

IPH-26B-5-125-11
IPH-26B-6.5-80-11

IPH-26B-6.5-100-11

3.齒輪油泵不宜在超負荷下工作，安全閥須按設備額定油壓調整壓力，嚴禁任意調整。NXQ-L0.25/10-H  
NXQ-L0.4/10-H   
NXQ-L0.63/10-H  
NXQ-L1/10-H     
NXQ-L1.6/10-H   
NXQ-L2.5/10-H   
NXQ-L4/10-H     
NXQ-L6.3/10-H   
NXQ-L16/10-H    
NXQ-L25/10-H    
P7600-F180NU3886/F125NPB-1蘭溪P7600-F160L3B察哈爾http://www.qihuiwang.com/product/q35527/261312163.html

IPH-26B-6.5-125-11
IPH-26B-8-80-11